Historical Tasks

Some of the tasks completed by the Shed Club are listed below

• Check Clubhouse door catch - sticking
• Blue rolls to the galley and eco-toilets
• Check Club House gutters
• Check flat roof gully
• Replace pontoon fenders and failed mooring lines
• Recover #8 racing mark and prepare to place the new race mark in the correct position with a new mud weight.
• Clean and check Safety 1 powerboat
• Straighten castor on 360 trolley
• HS2 Teams meeting at 10:30
• Resecure CB pin in club Wayfarer
• Replace starboard buoyancy-tank bung in club Kestrel
• Free hinges on fuel store doors
• Cut Camp Site grass.
• Brush the main pontoon.
• Meeting with EWR at 10:30
• Refit the pipe box to the water heater.
• Put the oppies back in the storage shed.
• Start scrapping "dead" boats to the skip.
• Modify the downhaul and reefing arrangement on the Club Wayfarer
• Sort and store tree tubes in the lower wood shed
• Check/replace broken coat hooks in the changing rooms
• Check benches in changing rooms and paint as required
• Check the pump on the main toilet water feed supply.
• Cut grass on the track to the south of the clubhouse and high level to the north.
• Other grass cutting as required.
• Finish tidy from Fun Day
• Fit insulation to the pipes on the new water heater.
• Metal skip pick up and waste skip delivery
• Change PSU in gate access control unit.
• Review Laser hulls, spars sails etc
• Set up a cask of beer in the bar.
• Set up, Aunt Sally.
• Put up the marquee.
• Install lighting.
• Clean/check Tug of War rope.
• Other prep for Fun Day
• Continue loading scrap-metal skip, it's collection is due on July 7th.
• .
• Check petrol stocks for training over the weekend.
• Delivery of replacement water heater
• Cut the grass on the campsite.
• Check and update safety bags.
• Continue loading scrap-metal skip, separate different metals and cut down as required.
• Continue replacement of racing marks
• Fix 15HP outboards.
• Investigate communications with access controllers in the Drott Shed.
• Connect 'power_fail' signal on the Gate access control unit.
• .
• Check tape on shrouds of all club boats
• Get the walker bay rib from storage and check for use
• Check petrol stocks for training over the weekend.
• Replace the mast gate on the Topper hull.
• Check the stock of squash in the bar.
• Check the power boats, extinguishers, anchors etc. including safety1
• Mark any defective craft/parts with tape.
• 
  Continue ditch clearing to the south of the clubhouse.
• Load scrap-metal skip, separate materials and cut down as required.
• Photograph the water heater and send it to the fitter.
• Check and prepare boats for training.
• Sort through spare cameras
• Check fuel levels for weekend training.
• Check sailing boats required for weekend training.
• Finish tidying up test pits.
• Bag kindling/logs for sale.
• Plan finish of blue container roof
• Finish work in the bar for cooler - box in extractor - construct box fit and finish
• Continue ditch clearing to the south of the clubhouse.
• Move new race mark #1 from office to container and inflate if required.
• Start the installation of new race marks.
• Cut and split some logs (needs Tractor)
• Cut grass on each side of the entrance to improve visibility.
• Cut the grass around the tracks.
• Cut Grass on Campsite.
• .
• Replace failed steps below the clubhouse (needs frost-free days)
• Adjust the new flail on the tractor.
• Cut grass between trees on the campsite.
• Meet Whadesden School Staff.
• Check fuel for the training weekend.
• .
• Set up and fit new flail to the tractor when it arrives.
• Investigate the poor surface on the upper end of the main slip.
• Strim grass around buildings and steps.
• Mount a second display screen in the training room
• Continue works for Outdoor washdown shower (Fix shower bracket)
• Fix the shower head.
• Cut grass on the campsite using a mower.
• Continue repairing awnings on the deck
• Continue ditch clearing to the south of the clubhouse.
• Dig test pits with Ground Engineer.
• Repair ruts created in the path south of the Clubhouse.
• Meeting with EPB at 14:00
• Collect Sausages from Padbury Meats.
• Collect Windsurfer from Winslow.
• Fit new locks to containers and put keys on the key block.
• Move the Bosun land trainer nearer to the containers.
• Continue repairing awnings on the deck
• Continue ditch clearing to the south of the clubhouse.
• Check the path at the western end of the site following EWR works.
• Align containers and secure
• Check craft and fuel for weekend training.
• Mount new tables by BBQ on concrete blocks.
• Clean and empty the Eco toilets.
• Move the Bosun land trainer back to level ground near the fence and clean it.
• Check and service the flail attachment for the tractor (broken)
• Continue preparation of the new BBQ area. (needs frost-free days)
• Clean, check/repair awnings on the deck.
• Check fuel stocks for Laser Open
• Assist moving Stowe sculls
• Move "compost" bins
• Tidy dead boat
• Finish works on C trot.
• More work on the trot area improvements
  • Finish levelling
  • Continue rolling the base
  • Finish/install tie-down stakes
  • Mark berths with numbers etc
• Collect RIB and OB from EPB and put them in the store.
• Meet Ground Stability Survey co at 11
• Meet with HS2 re-works at the lower car park and beyond
• Check water flow at overflow from Jubilee Reserve Lake
• Apply a second coat of oil to tables and benches on the decking area (needs to be dry)
• Review cover attachments on the dock for Safety 1
• Collect 3 serviced OB from Barrus (Paul)
• Prepare Rib for towing and tow to Barrus (Tony)
• Adjust the chimney on the training room stove.
• Check the route to be used by EWR to access the fencing area.
• Find the western gate key to loan to EWR.
• Meet EWR to confirm access for fencing work.
• Main Gate service by Gatecare.
• Check/sweep the chimney on the clubhouse fire.
• Tidy training room ready for First Aid course, stock firewood etc.
• Lift Mud weight near the main pontoon
• Engines to/from Barrus
• Move anti-slip strips on the deck by the race hut.
• Move the training computer to the clubroom and set up for an event
• Finish cleaning and other work on the Committee Boat.
• Get the Committee boat back on the water with the engine.
• Clean clubhouse lock release
• Replant failed laurel plants
• Check mast head sheave on club wayfarer (Haliard jamming)
• Finish trimming the willow tree on the beach and clear branches
• More work on the trot area improvements
• Find fenders
• Take the Safety boat off the water and prepare the engine to go for service
• Check topper dinghies by main slip and put them in an appropriate place
• Replace the soft board on the main pontoon ramp.
• More work on the trot area improvements
• More work on drum tables.
• Fit Led lamps in the training room fittings.
• Move cut logs to behind the clubhouse for splitting.
• Sort the waste wood pile.
• Check the network cable in the office that was not working
• Check and prepare the plant trailer for an outing.
• Reconnect the outside tap.
• More work on the trot area improvements
• Check tools and equipment for the workday.
• Trim vegetation on the circular path.
• Clean up the Dumper ready for return.
• More work on the trot area improvements
• Clean up roadways (mud)
• Clean decking (mud)
• Finish replacement of the float valve on the cistern in the Access toilet.
• Remove lugs on flagpole
• Show the Pirtek fitter the tractor
• Check RS Vision sails
• Take delivery of the hire machine
• Put new covers on Kestrels
• Investigate lights in the training room
• Check the flooded ditch by the main gate
• Work on tables
• Work on improved berth area
• Construct supports for the small race number board on the committee boat
• Check battery type in Egress lights on the clubhouse
• Take delivery of new freezer and place in Bar container
• Modify the setup on the race hut computer
• Check the flooded ditch by the main gate
• Fix leaking pipe in access toilet.
• Clean air filters on gas heaters.
• Prep training room for Weekend courses check the flue and firewood stocks
• Continue preparation of the new BBQ area.
• Bag logs for sale.
• More work on drum tables.
• Unload the Rigiflex 360s and prepare them for use.
• HS2 meeting
• Prep training room for Sunday course, network cables, fire
• Continue preparation of the new BBQ area.
• Bag logs for sale.
• Check the flooded ditch by the main gate.
• Collect and freeze sausages
• Continue preparation of the new BBQ area.
• Bag logs for sale.
• Clean decking
• Sort the leak around the window in the race hut.
• Continue preparation work to update the trots: strip topsoil......
• Prep trailer and Rigiflex boats for the tow to Lymington.
• Check the flooded ditch by the main gate.
• Bag logs for sale.
• Continue preparation work to update the trots: strip topsoil......
• Mark the cracked Rigiflex hull as out of action and remove the outboard
• Fix the rudder clip to Topper
• Lift mud weight near the main pontoon, marked by the divers.
• Investigate the flooded ditch by the main gate.
• Finish stakes for Stowe boats.
• Continue preparation work to update the trots: remove stakes......
• Install an access point in the training room
• Continue preparation of the new BBQ area and complete spreading of woodchip.
• More work on drum tables.
• Continue preparation work to update the trots: remove stakes, cut trees, and clear scrap ......
• Continue works for Outdoor washdown shower (Shower head and control)
• Complete the network connection to the training room
• Work on drum tables.
• Continue updates to lighting in Drott shed, update fixed wiring, reinstall repaired lamps, and remove others for repair.
• Continue preparation work for the update of trotts.
• Make boat stakes, cut angle to length, and attach a chain (weld)
• Continue works for Outdoor washdown shower (plumbing and panel)
• Check fuel for weekend training
• Sort equipment for training
• Continue preparation of the new BBQ area and complete spreading of woodchip.
• Replace batteries in failed emergency lights
• Updates to lighting in Drott shed, update fixed wiring, reinstall repaired lamps, remove others for repair.
• Preparation work for the update of trots
• Continue works for Outdoor washdown shower (plumbing and panel)
• Check/pump out the work pontoon or alternative for Spooky Fireworks
  Check anchors for pontoon
• Identify the type of batteries needed on emergency lights and order.
• Repair lamps in Drott shed
• Repair tractor steering wheel adjustment mechanism.
• Test emergency lights
• Upgrade firmware in the firewall
• Check dates on First Aid box contents
• Check toilet rolls for mummy wrapping (Halloween)
• Check the hooter on the committee boat
• Continue preparation of the new BBQ area and complete spreading of woodchip.
• Work on drum tables.
• Check wheels on club boats
• Put the replacement centreboard in Wayfarer
• Check the emergency light in the workshop.
• Continue preparation of the new BBQ area and complete spreading of woodchip.
• Work on drum tables.
• Check the roof angle on the clubhouse
• Replace the battery in the Committee Boat
• Find the fault in the bar/galley/lady's lighting circuit (Roger B)
• Defrost Freezer in the galley
• Continue preparation of the new BBQ area, finish base for BBQ and work on drum tables.
• Check emergency lights
• Find and check the windsurfer for Safety boat training.
• Continue preparation of the new BBQ area, form a concrete base for BBQ, select drum for table define timber requirements
• Work on Drum pick
• Put Slalom buoy lines on new drums.
• Start cleaning and reassembly of 6th kestrel (back from repair)
  Put the club wayfarer on the new trolly and adjust as needed
• Check Kestrels and do some preparation for weekend training
• Committee boat, Charge battery and test OB
• Replace the battery in the portable jumpstart box
• Move 5th kestrel to the main ramp area
• Check fuel stocks
• Freeze sausages
• Start measuring the power consumption of key equipment
• Bag some firewood for sale in the clubroom.
• Paint Numbers on racing Buoys
• Stock check training books
• Measure power used by IT
• Reduce the height of the surface under the main gate
• Review benches on decking and adjust as required
• Look at handrail on decking, review fixings and levelling of decking
• Bag some firewood for sale in the clubroom.
• Start preparation for the new BBQ area
• Bag some firewood for collection at lunchtime
• Meeting with Network Rail.
• Check the office computer, (not booting correctly)
• Repair ramp onto main slip, replace rotten timbers, check pivots and fixings
• Sort storage for slalom buoys.
• Continue works for Outdoor washdown shower (plumbing and panel)
• Grass cutting as required
• Cut back vegetation to the left and right of the gate to improve the sight line
• Investigate floor in Eco toilet
• Repair waste pipe from Bar to gully
• Move buoy 9 3/4 to the correct location
• Lift and reposition mooring buoy #3
• Finish mulching new trees
• Renumber buoy to 10 from 11
• The club Wayfarer replace the broken clip on cover
• Review/fix danbuoy drums and moorings (one weight is too heavy)
• Replace 9 3/4 buoy
• Change fixings (bolts) on tent A-frames
• Work on the outside shower
• Renumber buoy to 9 3/4 from 10
• List boat berths for scouts to get SCM up to date
• Assist with the moving of containers
• Set up the blue container in the new location, roof etc
• The club Wayfarer main halyard is binding, we need to check the top pully
• Install a new access point in the clubroom
• Install a new access point to the training room
• Recover 9 3/4 buoy
• make mud weights
• Prepare an area for storage of wood chip
• Move two heaps of wood chips to the new location
• New woodchip to eco toilets path
• Install new network wireless link to Drott shed
• Move timber to the wood pile
• Move large pieces of steel to the scrap pile
• Move the rowing boat and trailers from containers
• Remove old stakes from the cleared area
• Fill in some hollows in the camping area
• Continue preparation of space for old container
  
• Replace broken tiller extension on Kestrel rudder
• Tidy up fallen branches and review trees near the boundary
• Finish tidy up from 50th celebrations,
• Clear the old BBQ site in the camping area
  
• Prep work for 50th celebrations,
  • Set up Aunt Sally
  • Bunting
  • Lighting and power in the tent
    Put up board
  • Prep BBQs
  • Set up beer casks
  • Set up displays
  • Tables
  • Sort sound system
  • 
    
• .
• .
• Build firewood trolley/storage for the clubroom
• HS2 meeting at 11:00
• Fix shelf for computer /printer in race hut
• Prep work for 50th celebrations, Find and check aunt sally, lights, bunting, power leads etc
• Change fixings (nuts & bolts) on tent A-frames
• Water trees if required
• Move craft for training
• Install yellow marker buoys
• Signs for the beach area
• Update the galley price list
• Review Kestrel dinghies and make fixes as required
• Check new tent
• Fill Metal Skip
• Prep power boats for Saturday Training
• Engine onto Safety 1
• Split the large bits of firewood by the wood store
• Review scrap trailers etc. - order skip
• Reposition the furthest mooring buoy
• Reposition racing mark #8
• Cut and split wood in lower woodshed and bag for sale
• Replace the grey water pump
• Rack Y - cut back vegetation
• Prep for HS2 works
  • Sort container content
  • Clear the remaining metal from the hedge
  • Break up boats for disposal and pack them in the skip.
• Check Toppers for Junior training on 21st
• Empty buckets (eco)
• Continue works for "wash down water tank" adjacent to the slipway Position LBC, connect up outlet
• Adjust the moorings of the mirror jetty
• Prep for HS2 works
  • Review boats that need moving
  • Move Bosun trainer
• Replace batteries in clubroom emergency lights
• Check Picos and toppers for Junior training on 14th
• Check and prepare powerboats for Junior training on 14th
  • Second Rigiflex 15
  • Walker bay rib
  • Green Inflatable?
• Check the Training room for weekend courses
• Mount a small screen in the small training room
• Initial works for Outdoor washdown shower (plumbing and drainage)
• Initial works for "wash down water tank" adjacent to the slipway Position LBC, plumbing outlet
• Finish adjusting the position of the new jetty and securing moorings
• Check fuel for training courses
• Replace motion sensor in access toilet
• Move mooring buoys near #8
• review moorings on the new jetty
• Cut remaining timber by the wood store to length
• Review training books stock - order as required
• Water trees
• Mulch around trees
• Get Sausages and Burgers
• Review batteries in clubroom emergency lights
• Repair the bilge pump electrics on safety 1
• Cut timber by the wood store to length
• Eco Toilet Bins
• Review Algal bloom and place signs as required
• Replace the roof on the firewood store by the clubhouse
• Grass cutting as required
• .
• Review wood in the lower shed and from HS2
• Fix safety 1 console
• Review Algal bloom and place signs as required
• Replace batteries on access control and computer UPS
• Replace racing mark #6 (now recovered to the slipway)
• Check Dan buoys and clean (ready for the open meeting)
• Replace mooring on pontoon by the south bank
• Put 2 kestrels back on their trollies.
• Paint Numbers on all buoys (ready for the open meeting)
• Complete the replacement of the steering cable on Safety 1
• Continue to plant trees in the camping area
• Finish race-hut, make and fit 2 shelves
• Review 15hp 2 stroke
• Plant trees in the camping area and near the new pond
• Move some wood chippings to the seat above the pond
• Continue to fix the electric mixer starter (Install a new contactor)
• Reposition new pontoon in readiness for ramp being repaired
• Put tree whips in a safe location (with spare laurel?)
• Safety 1, test and place on the moorings
• Fix mixer starter (Diagnose)
• Clean hull on Rigiflex (Safety 1)
• Unload Siddals delivery
• Collect timber from fallen trees
• Repair fence damaged by tree
• Check new batteries in woodshed and eco-toilets
• Collect 15HP and 30HP from the service
• Knock down old BBQ on the campsite and clear for replacement.
• Install outboard on Committee boat, test and place on the moorings
• Repair hinges on cupboard doors in the training room
• Clear the fallen tree from the road verge
• Bag some firewood for sale
• Recover pontoon ramp parts from water
• Check plant trailer (for collection of ballast)
• Create access to the fallen tree internally.
• Turn on the greywater pump and check its function
• Check access control computer and restart as required
• Move the ramp for the new pontoon out of the water and inspect.
• Replace the NW mooring on the Mirror Jetty
• Work on fallen trees esp one in the SE corner of the site
• Plant more laurel
• 15HP and 30HP OB to barrus
• Put Bodpave and shingle track side of the rack, Geotex under the rack
• Plant more laurel
• Move more topsoil between canoe rack and old car park
  Replant laurel in front of canoe rack
  Prepare posts for the new canoe rack
• Check tools for Saturday's workday (strimmer etc)
• Continue to dig settlement pond adjacent to school hill
• Mark area that needs clearing for HS2 de-veg
• Replace mooring ropes on the pontoon near the south shore
• Clear fallen tree in cops adjacent campsite
• Clear trees and shrubs for an area of the settlement pond
• Clear shrubs as needed for ditch work on school hill
• Define location for new kayak rack
• Swap battery in the Eco Toilets
• Strip scrap boats for disposal
• Install replacement gate at the western side of the site
• Fell and clear hanging tree in woods to the south of the site
• Clean projector lens in the clubroom
• Clean decking
  Finish modifications to the Topper trailer
• Move some boats
• Make tie-downs for new berths in the lower boat park
• Check the work Gatecare have done on the gate.
• Make new tie-down stakes for general use.
• Fix roof sheet to frame on blue container
• Bag some firewood for sale
• Use plastic strips to protect the wood store from rain.
• Sort the latch on the clubhouse door
• Clear fallen trees in the Northwest corner
• Fix roof frame to the blue container
• Bag some firewood for sale
• Finish the installation of the access controller for IS
• Check tie-downs on club boats (High winds forecast)
• Construct frame for roofing the blue container
• Bag some firewood for sale
• Stop the leak in the Bar Container roof
• Start the installation of the access controller for IS
• Clear the path to the NW corner
• Swap the battery in the wood store
• Tidy some rubbish
• Swap padlocks
• Continue recovery of racing mark #7
• Refix entrance signboard
• Tidy lower woodshed
• Change/check the oil on digger track gearboxes
• Dismantle floodlight/ weather station pole
• Refix notice board next to lower slip
• Create a new scrap metal stack
• Tidy Workshop
• Prepare for Spooky 21 - tent, pumpkin...
• Empty ECO buckets
• Remove shuttering on the tank base
• Check model/serial numbers on small inflatables
• Put catches on cooker door
• Bag some kindling for sale to members
• Fit new belt to ride on mower
• Install and test the new printer
• VTS to fit new tyres on tipping trailer
• Concrete base for oil tank
• Move working pontoon
• Check campsite for Waddesdon School
• Find and label the charger for the power pack
• Review communications to access control on the Tug store
• Rope of waterside of the area by dan buoys
• Review waterside area with a view to replacement
• Check stock of sausages and order if required
• Boat moves
• Continue toe strap floor fixing on kestrel and leak in the same boat
• Grass cutting
• Continue painting the Clubhouse door and Office door
• Lift redundant mud weight for the new pontoon
• Mark out new container positions
• Continue to tidy rubbish heaps at the back of the new boat park area
• Sort kestrel leaking centreboard bolt
• Tidy around Hazel tree planting
• Sort covers on Pico dinghies
• Continue painting the Clubhouse door and Office door
• HS2 boundary meeting
• 15HP outboard to Barrus
• Improve fire door closing
• Measure volume of clubroom and training room
• Read the electric meter and submit
• Check stock of pies etc.
• Cut back hedge behind clubhouse and wood store
• Set up movement detector on training room OS lights
• Review ditch adjacent to School Hill.
• Replace lead on mains compressor, chewed by mice!
• Review repositioning of containers for HS2 boundary
• Tidy rubbish heaps at the back of the new boat park area
• Continue barriers around the new boat park
• Replace emergency egress lights and floodlights on the corner of the training hut.
• Trim back bushes on each side of the main steps, as they are over the handrail.
• Prepare boats for training.
• Check outside floodlights, clean sensors etc.
• Move some seasoned wood up to the back of the clubhouse for cutting/splitting
• Check tape on all shroud plates
• Create an access route to compost bins
• Finish improvements to the path to Eco Toilets, chips and boundary
• Paint Clubhouse door and Office door
• Grass cutting on camping area and elsewhere if time
• Sort main sheet block on RS Tera, spring is in race hut
• Review area where the aluminium track has been lifted
• Prepare the area for stow rowers storage
  
• Replace the fob reader on the Tug store
• Move logs
• Cut down bush
• Prepare the surface for membrane and stone
• Review kestrel with damaged thwart
• Sort toe strap on pico dinghy
• Sort Pico and Laser trolleys
• Continue to prepare the area for trailer storage
• Prepare the surface for membrane and stone
  Lay membrane
• Lay stone
• Read the electric meter
• Key fob
• Prepare area for trailer storage
  • Move trailers already in the area
  • Clear other items
• Install metal post on edge of dragon boat park area
• Move toppers to shore for Grebelets
• Install barrier posts
• Assemble club wayfarer
• Cut grass where boats have been moved
• Move Topper trailer to the foreshore
• Repair toe straps in RS Feva
  Try to keep dry (failed)
• Tidy up area adjacent to containers (bag ballast, sort trailers, move the large boat, cut grass)
• Reinstate Bosun trainer.
• Move remaining club boats from the campsite
• Water beach area turf. (investigate pump problem)
• Check the door and latch operation on the Tug store.
• Check boats for Junior sailing including toppers (one has a missing bolt on a bailer)
• Tidy up around canoe rack
• Assemble Kestrel back from repair
• work on scout area
• Prep club wayfarer to go for repair
• Create barriers around the new boat park
• Check tension on excavator tracks
• Finishing touches to works
• HS2 snagging meeting
• Service visit for Tug repair (10:30)
• Check/clean Eco toilets
• Put away Walker Bay rib in roof
• Test pump, hoses and sprinklers for turf watering.
• Swap trailers under Rigiflex 360 boats
• HS2 meeting
• Check Pico dinghies for adult training
• Move some boats
• Works around new berths and car park
• Sort area for boat storage near containers
• HS2 meeting
• Review and update moorings on the new pontoon.
• Review and plan signage around the new pontoon
• Move excavator to the eastern end of the lake in preparation for post-mitigation works actions
• Tip and level pea shingle by main slip.
• Check boats (terra and topper before 26th June)
• HS2 meeting
• Empty "buckets"
• Tidy Pico cabin
• Tidy Drott shed
• Check TC stocks
• Clean showerheads (descale) and flush shower feeds
• HS2 meeting
• Check defib pads and order replacements
• Check First aid kit dates of materials and order as required
• Get Digger hose fixed
• Trim willows on beech
• Clear weeds on main steps from the clubhouse
• Replace extractor fan in men's changing room
• Update instructions for Safety 1 cover removal and installation
  HS2 meeting
• Read the meter and submit it to BGL
• Improve weight on orange buoy marking closed area
• General grass cutting and strimming
• Repair pipe to the outside tap
• Collect from Padbury Meats
• HS2 meeting
• Scrap metal skip collection
• Inflate tyres on the tractor-trailer
• Prep for Weekend, Signs, Bar container, clean BBQ
• Tighten bolts on flail TPL frame
• Replace tyre inflator on compressor
• Launch RIB, run the engine and check oil levels
• Get mud weights to the water's edge
• Drainage pipes could be used on the path that floods by the new pond
• Place mud weights for the new pontoon
• Check centreboard lines on Kestrels
• HS2 meeting
• Service flail - replace belts, grease, clean as required, fit new PTO shaft.
• Move club craft back to main slip (Kestrels, Wayfarer, RS Visions)
• Oil and filter change on 40HP (Barrus)
• Descale urn
• General grass cutting
• Continue reassemble Kestrels returned from the refurbishment of hulls
• Tape shrouds on club craft as needed.
• HS2 meeting
• Check the status of the windsurfer in compound
• Shutter and cast shore anchor points for the new pontoon
• Review new pond outflow
• Review position of Fishing pontoon
• Cut grass on the camping area
• Improve path to the east of the new pond
  Last ridge piece on lean-to shed roof and finessing details
• Read the electric meter and submit the reading to BGlite
• Refine mounting of cover on safety 1 and produce draft instructions.
• Move mud weights for the new pontoon
• Position mud weights for the new pontoon
• Move old long jetty and position for fishing boats
  Level the path from new pond to Eastern spoil heap top
• Replace roof on lean-to store
• Safety 1 and committee boat to jetty ready for new cover fitting at 2 o'clock
• Move Bosun land trainer
• Engine onto safety 1 and ready for launch
• .
• Move material from middle pond to path side
• Review/repair plant trailer bed
• Scrap metal to skip
• Tidy Dorry
• Sort road base for moving Kestrel to repairers
• Prep mud weights for the new pontoon
• Review work needed under main pontoon ramp.
• Read the electric meter and submit the reading to BGlite
• Finish work on the new pond
• Dig out some (1/3) of the reeds etc. from the small pond and replant in the new pond
• Build second "compost box"
• Roll grass on the extended camping area
• Continue to tidy up committee boat
• Check electrics on the committee boat
• Review cover on Committee Boat - Sparks to measure up on 9th
• Continue work on new pond subject to water level
• Move "work pontoon" from the beach area
• Relocate fishing pontoon to protect cofferdam sort moorings first
• Investigate bank at the western end of the beach
• General grass cutting
• Prepare damaged kestrel for travel to repairers
• Re-bag firewood for sale to members (in the woodshed)
• Committee boat, remove outboard for winter storage
• Split rings of the fallen tree for firewood
• Get Committee boat out.
• Check boundary near playing fields and add fence panels as required.
• Replace first aid box
• Check pontoons
• Check main lights in clubroom/replace the switch
• Movement of Dragon boats
• Check water depths for new slip works
• Photograph cover on the committee boat and send to sparks marine trimmers for replacement pricing
• Preparation for centre inspection
• Discussions/planning around HS2 works
• Continue to trim bushes in front of the race hut
• Install battery in access control for Tug
• Sort main printer in the office, it keeps stopping
• Meetings with HS2 - ecology
• Meeting with Land Agent
• Deal with brash and rubbish pile
• Define pond remodelling.
• Pick apples
• Move more wood for club fire
• Sort stored timber
• Clean RS Tera dinghies and cut grass around them
• General grass cutting
• Trim more of the bushes below the clubhouse
• Check OB serial numbers
• Sharpen loppers
• Cut grass etc at the gate to Charnon Road
• Hose replacement on excavator -engineer booked
• Remount no swimming sign near "mirror jetty".
• Investigate #7 buoy, reported as having moved
• Empty some eco-toilet buckets
• Move some topsoil to finish off round race hut
• Replace retaining clip on gear linkage in Dorry 30HP engine (have new clip)
• Work on "work pontoon" winch
• Tidy up club boat berths near drott shed, relocate timber
• Started to trim bushes in front of race hut
• Kestrel moved back to its berth
• Replace the last fan in eco-toilets
• Empty Eco buckets
• Insulate roof on race hut and recover.
• Fit gutter on race hut
• Check engine control cables on safety 1
• Check through Pico dinghies and sort trolly tyres and bungs
• Replace covers on Vision and Feva dinghies
• Replace toe straps as required in Feva dinghies
• Refurbish "Laser Trainer"
• Check sensors on the gate and investigate the reason for problem earlier in week
• Adjust door sensor in Tug store
• Descale shower heads
• Build extension of decking by race hut
• Prepare clubhouse for re-opening
• Clean Safety 1 and check
• clean jetty
• Check committee boat
• Review fuel store
• Put up shelves in race hut
• Complete line out of race-hut with insulation and OSB
• Continue work on tug kennel
• Put Tug in Kennel
• Make additional mud weights
• Lay concrete outside tug store
• Strengthen race-hut structure.
• Preparation of pad for deck extension
• Replace sealant round whb in lady's
• Replace sealant round whb in men's
• Continue work on tug kennel.
• Unpack, set up and check replacement chop saw
• Setup access control for tug store
• Start to line out race-hut with insulation and OSB
• Install the new drain and underground pipes for Drott Shed rainwater
• Some work on tug kennel
• Check new fencing
• Fit door in race hut
• Lay concrete base for "Tug kennel"
• Run CAT5 cable from workshop to door end of Drott shed
• Move skip
• Move scrap boats to skip
• Cut up scrap boats and put them in the skip
• Cut grass, cut grass, cut grass, paths and roadside.
• Clean the jetty
• Investigate bank slip by the seat on the south bank, erect barrier or make safe
• Move chipper from the car park
• Check tyres on tipping trailer
• Prepare for "Tug Kennel"
• First fix cables in new race hut
• More equipment move to the lower car park
• Run pipe across the path near the first seat on the south bank (dig, dry sandbags, pipe, backfill)
• Move scrap boat to skip
• Run power cable to slipway area
• Move excavator to the lower area
• Complete work on safety 1 and committee boat
• Work on supply cables to race hut
• Continue work on race hut construction
• Find and cut deck boards for deck extension
• Swap access control computer
• Engines back on safety 1 and committee boat
• Pull cables through clubhouse roof for race hut power
• Continue work on race hut
• Check what is required for #6 buoy replacement
• Plan Workday
• Committee boat trailer - reverse suspension units or swap axle bar
• Check what is needed for fishing pontoon
• Construct timber frame for new race hut base
• Committee boat - check over and decide on work needed before next season
• Check over safety 1 and prepare for next season
• Prepare the last kestrel for refurbishment
• Move cleaning materials
• Continue to dig out of race hut base
• Make shuttering for pads
• Bore foundation holes
• Concrete foundation pads
• Make mud weights
• Continue Refurbish "Laser Trainer"
• Continue to Refurbish main land trainer (Bosun)
• Committee boat off the water and remove the engine
• Prep for workday
• Dismantle race hut
• Powerboat trailer
• Continue Race Hut clearance
• Prep for end of season
• Split some firewood
• Review hydraulic pack and breaker
• Review main land trainer (Bosun)
• Get ballast
• Started to refurbish "Laser Trainer"
• Clear up in bar container
• Update computers
• Dispose of some rubbish
• Sort through "stuff" stored over the workshop and inner sanctum, review: keep - scrap - recycle
• Replace dimmer in the clubroom
• Finish container turnout.
• Erect and dress tree
• Trailers into scrap metal skip
• Turn out containers
• Topper in metal skip to plastics trailer
• HS2 meeting
• Cut up trailers and metal to skip
• Check and sort mark #3
• Check and sort mark #9
• Look at throttle cable on the committee boat, reported sticking
• Finish clear up after tree work, cut, move and stack larger timber, split for kindling
• Waste skip out, metal skip in
• Clear up after tree work, chip brash, move and stack timber
• Scrap metal skip out, waste skip in
• Cut up some more craft for waste skip
• Assist tree work, moving brash, chipping etc.
• Prep for Spooky
• Look at HS2 test pit reinstatement
• Light in Men's
• Bag some firewood for sale to members
• Firewood to store by the clubhouse.
• Rubbish skip out, Metal skip in.
• Scrap metal to skip
• Label bottles of apple juice
• Get "Race Hut" camera working - replace broken coax cable
• Look at rudders on Kestrels - tighten and adjust as required
• Sort padlocks - fuel store/inner sanctum.
• Move boats and plant to allow access for HS2 test pits
• Pick apples
• Check/repair round table and wooden chairs on deck and store for winter
• Investigate race hut and deck level
• Second 15HP tiller to Bicester for service
• purchase grease and gun (UU1021)
• Grease digger and logging trailer
• Fix lights by gate only one working
• Test knapsack sprayer
• Check boats for the training weekend
• Electric meter reading
• Check 15HP tiller/change plug?
• Look at lights on the training room, flood light not working.
• Look at floods on the clubhouse, Main not working and one gate light only working.
• Prep required for Terra Open - TBD
• Clean Pontoon
• Sort DAN buoys - one needs cleaning - one needs replacement line and weight - check rest
• Cut grass/weeds on the campsite
• Let Skip driver in to swap skip over
• Cut up more boats that are to be scrapped and pack in skip
• Read electricity meter and submit to BG
• Check gate sensors as it has been reported not opening
• Check Eco toilets and empty buckets
• Cameras not updating on website and unable to connect VPN - check - Call Village networks to change IP (TG)
• Direct Skip driver to the required location.
• Cut up boats that are to be scrapped and pack in skip
• Check racing mark #3
• Replace racing mark #3
• Clear vegetation in the lower boat park area
• More boat moving
• Make mud weights
• Supervise Gatecare for Service visit.
• Cut grass, paths and roadside
• Remount floodlight on bar container
• Look at Rigiflex 360 #3 define repair plan
• Replace Pico jib sheets as required
• Trim kestrel main sheets as required
• Look at pipes on edge of the area by dan buoy storage
• Replace batteries in cordless phones
• Fit new padlock to the gate
• Check Bass Boat
• Look at the sailing craft for water week
• Check fuel stocks for powerboats
• Clean Pontoon
• Check training room
• Repair wood store roof
• Look at floor drains in men's changing room.
• Fit third blind on deck
• Repair Pico rudder
• Empty ECO buckets
• Check/sort freezer
• Work on the temporary trailer for RIB, improve balance, swap winch and snub with the other trailer, Improve roller uprights
• Collect and test RIB, sort temporary trailer
• Put new Laser radial sail on a mast
• Read the electric meter and submit
• Prep for the open day
  • Set up cask beer
  • Clean pontoon
  • Put up tent
  • Sort shades
  • Check boats (generals and specifics below)
  • Check BBQ
  • Store food
  • Get dragon boat on the water
  • Check kyaks
  • Check eco-toilets
  • Bunting
  • Displays
  • Clean deck
  • ..........
• Look at display boards for Open Day
• Cut grass, paths and roadside
• Update sign for fuel oil mix(100:1) with quantities and put in lid
• Continue work on Club Wayfarer - test tanks
• Replace cleat on Wayfarer mast
• Kestrel 1485 check, the main sheet cleat reported missing.
• Kestrel sail 1493 replace yellow reefing line - it is to thick.
• Kestrel 14?? sort out centre board raise/lower line - it has been "rethreaded" following elastic fail
• Cut grass on the campsite, out front, paths
• Kestrel sail 1485 replace short second reefing line
• Scrap metal skip to be collected (10:00 - 12:00)
• Replace the battery in the smoke detector, training room
• Tidy round carpark - grass/weeds etc for the open day
• Strim vegetation in the lower boat park area
• Remaining scrap metal to skip
• Check/replace lamps in the training room
• Create signs for fuel oil mix(100:1) and put in store lid
• Refurbish shower waste pump in access toilet
• Investigate mooring buoy #3.
• Investigate shower waste pump in access toilet
• Sort and clean scrap metal into the skip
• Abandoned craft, strip then cut up and put in the skip
• Rake out slots in decking
• Sort craft in abandoned boat compound.
• Cut vegetation on the newly capped area (100 - 200mm)
• Investigate leak in small inflatable's "airdeck"
• Replace racing mark #10
• Re-assemble repaired Kestrel
• Look at solar panel and battery charging on Committee boat
• Paperwork for weekend training
• Check fuel
• Stock bar
• Clean jetty before the weekend
• PTBO preparation
• Replace main halliards in RS Visions
• Remake loops on RS Vision jib halliards
• Replace horse block on Tera boom
• Grass cutting
• Tidy up carpark (for PTBO)
• Other PTBO preparation.
• Stocktake on Training books and certificates
• Clean jetty before weekend's training
• Clean whiteboard in the training room
• Review steps from the clubhouse to slip (do we need to do anything before PTBO?)
• Setup and test replacement fryer
• Compact hard-core round canoe rack
• Check/ replace outboard fuel lines
• reassemble Kestrel back from repair
• PAT testing part 3
• Canoe rack, mark bay numbers
• Canoe rack, complete assembly
• Sort tyre on tractor tipping trailer
• Fill the hole in entrance apron
• Test egress lights after battery replacement
• Canoe rack, start erecting posts.
• Check 2 stroke fuel and 15HP engines
• Check water meter reading (needs pumping out)
• Continue work on Club Wayfarer - replace hatches
• Prep next kestrel for repair
• Dory get back on the water for Saturday (engine on etc)
• Third repaired kestrel - reassemble, new painter, horse etc.
• Modify Dory cover to simplify mooring
• Continue work on Club Wayfarer - replace hatch seal tape.
• Replace padlock on the gate at the west of the site
• Dory second coat of paint below the waterline
• Clean Dory hull and paint below the waterline
• Gate service visit and interlock check
• Get safety 1 into pontoon and replace steering helm and cable
• Committee boat back together and launch
• PAT testing part 2.
• Returned engines to store
• Check steering and bilge pump on Safety 1
• Make up more fuel lines.
• Prep work for next workday, materials check, drill posts
• PAT testing
• Bag some firewood for sale or prep for collection.
• Cut trees and overhanging branches down near the high seat
• Replace power supply for the camera on Drott shed
• Sort through extension leads and work out a better storage
• Check Committee Boat and make a list of tasks for February
• Clear round wast water lift pump chamber and check
• Investigate crack in safety 2 hull - plan action
• Make fuel lines
• Measure Kestrels for covers
• Paint floor of Kestrel back from repair
• Check emergency lights in the training room
• Check Fuel cans and lines.
• Replace batteries in egress lights
• Started new canoe rack (holes dug)
• Any tidying up before the RYA meeting on Monday 21st
• Replace the battery in safety 2 and test boat ready for PB course
• Second coat of paint on walls of cubicles in Ladies if required
• Check pico rudders - elastics tight, any breakages etc.
• Check club boats tied down.
• Pumpout/check safety 2 - the battery may be flat
• Clean pontoon.
• Christmas decorations down and away
• Check emergency lights
• Prepare next Kestrel for repair
• Mount Screen in the training room
• Get repaired Rigiflex back to service
• Split some firewood
• Set up Vonage IP phone unit when delivered
• Clean deck and check warning signs
• Get damaged Rigiflex ready for repair, lights etc.
• Check bilge pump float switch on safety 1
• Paint walls of cubicles in Ladies
• Investigate battery on committee boat (flat on Sunday)
• Chip brash from tree pruning
• Check bilge pump float switch on safety 1
• Prep some firewood.
• Clean Cameras
• Continue work on the rowing boat
• Get damaged Rigiflex ready for repair, photo of the damage to the repairer
• Continue work on Club Wayfarer (finish reefing lines)
• Finish box in pipes in Lady's change
• Seal the hole in RS Tera and replace hatch seal - test hull
• Work on / re-assemble Kestrel back from repair work
• Jetty cleaned
• Work on "new" tender
• Kestrel floor painted (mike brought some in) ready for re-rigging.
• Wheels moved on the double axle trailer.
• Halloween stuff put away.
• 2 padded chairs darned.
• Hose from down the steps tided.
• Cement on-site for canoe posts.
• Pump out pontoon used by Raden Engineering
• Recover pontoon used by Raden Engineering
• Replace brushes in the chop saw
• Label the second batch of Apple Juice
• Prep work for Work Day - find tools etc
• Workday task planning and materials
  • List jobs on Kestrels for the workday
  • canoe/kayak rack planning
    Splice Lines on fenders for buoys
    Start fixing fenders to Mirror Jetty
• Label bottles of apple juice
• Replace valves on men's showers
• Install lights in men's showers
• Replace hand dryer in men's
• Prepare pontoon for Raden Engineering
• Fit divider in men's shower
• Check bilge pump electrics on safety 1 and 2
• Prepare pontoon for Raden Engineering
• Repair craft fault report folder
• Check engine serial numbers
• Replace broken hooks in changing room enlarge to 4.5mm clearance hole, use 4.0 x 40 screws
• Produce food allergens folder
• Sort tiedown for club Wayfarer - cut a hole in the concrete and fix a chain
• Sandbags around the new ramp.
• Pump out work pontoon
• Clean main jetty
• Mark up/colour code more of the Drott shed storage racks
• Move mud weights to the water's edge
• Replace Number 9 racing mark (chain failed)
• Fix flood light by the main gate
• Check flue mounting on the training room
• Pick apples
• List all dead boats and photograph
• Investigate and tighten up handle on clubroom door
• Check fuel
• Make mud weight for #9 + spare
• Continue work on Club Wayfarer (mast step)
• Rebuild a kestrel for use in the training weekend
• Yet more boat moving
• More Boat moving
• Painting/varnishing boat parts
• Construct compost enclosure
• Prune more trees on route for Rayden Eng.
• Get Kestrel #6 back to drott shed and restore fittings
• Change engine on Safety 1
• Boat moving
• Replace shock cord on committee boat cover
• Replace shock cord on pico toe straps
• Replace main cleat starboard side on 1 pico
• Sort cleaning supplies
• Finish update of Eco toilet signs
• Look at access toilet shower waste pump - not running automatically
• Replace shock cord on rigiflex lockers
• Check fixings on Rigiflex for stressed screws
• Tighten fixings on safety 1 bow cleat
• Replace shock cords on safety 1 cover ridge pole and stand
• Clean/lubricate padlock on Safety 1
• Pickup and move cuttings from ditch clearing
• Find or replace MOB buoys for training use - create a storage location
• Check solar charger on Committee Boat
• Replace fuel line on a tank in flamstore
• Move boats by dead boat pen to allow Rayden Eng access
• Fix shelf in the kitchen cupboard
• Sort Kestrel to go for repair
• Investigate lift on 15hp outboard
• Investigate eco-toilet cubical light, reported on all night
• Fill rubbish skip
• Finish off round stopcock cover
• Check parts required for flail and order
• Prepare Eco toilets for the third unit - clear cubical, door catch, cubical light, door sign, instructions
• Test Safety 1 - battery reported flat, not used last Sunday
• Signs - campsite rules, beach area, car park notices need fixing (replace drawing pins)
• Finish loading skip with scrap metal
• Collect up windsurf boards and hide
• Review centre inspection action and plan actions on boats
• HS2 Meetings
• Clean gate sensors (playing up)
• Review centre inspection action and plan actions on boats
• Replace hinges on main clubroom door
• Straighten door closer
• Sort battery on Dory (swop from the committee boat and use small on committee boat)
• Clean Solar pannel on Committee Boat
• Load skip with scrap metal
• Check power boat kits and extinguishers
• Make up a short tiller extension for H15
• Work on Club Kestrels specifically rudders
• Assemble and fit wind indicators
• Ride-on mower - Get it running smoothly, work on cutter blade
• Put up car park signs
• Prep work for the open day
  • Tent up
  • Check food stocks
  • Collect meat from the butcher
  • Collect beer
  • Floatation test on kayaks
  • Displays
  • Feather flags
  • ...........
• Mark up new buoyancy aids
• Treat wooden coat hooks
• Continue work on Club Wayfarer
• Look at engine lockdown on Dory - reports of lifting in reverse
• Prep work for Stow work party
• Replace broken hooks in men's with wooden ones
• Tidy up timber stock behind the clubhouse and alongside Drott shed
• Check trolly wheels on Pico dinghies
• Clean out the club room fire for summer!
• Repair centre main fitting on RS Vision
• Ride-on mower - Carb back on
• Mountfield mower - get it running again!
• Swap remaining clubroom lights
• Investigate Drott shed lights
• Clean gutters around the clubhouse, check the filter on rear downpipe (seen overflowing)
• Treat wooden coat hooks
• Prep for Barrus Day
  Cut grass round gate sensors
  More Grass CuttingFinish reposition of "new" ramp (add shackles)
• Mountfield Mower - remove Blade bolt and sharpen the blade
• Replace some clubroom lights with LED lamps
• Tape Shrouds on club boats
• Repair Kestrel rudders.
• Varnish oppie foils
• Spread 18t shingle on car-park
• Sort bits in "Inner Sanctum"
• Recover 'lost' mud weight
• Grass cutting
• Preparation for PTBO
• Work on club Wayfarer
• Paint walls in men's cubicles